Skip to main content

Upper Structure

Cut Lengths Worksheet

Use the worksheet below to calculate board cut lengths relative to the length and width of the solar panels.

Screenshot_2023-05-22_11-39-02.png  image.png

Board Size

Name

Expression for Cut Length

Length

2x8

Main Support

(Solar Panel Length) - 2.5in =


4x4

Horizontal Support

(Solar Panel Width) x 2 - 2in =


2x4

Vertical Support

(Solar Panel Length) + 4.5in =

 

Main Support

Drill a 7/8” hole through the Main Post, 1 ¾” from the top.  The large 7/8” diameter allows the design to tolerate a hole that is not perfectly level (up to +/- 1/8” variation at both ends).

Using 2x8 boards, cut two Main Support boards to the length written on the worksheet (above).  Drill an 11/16” or 3/4” hole near the center of each Main Support, 2 ¾” from the top edge.  Attach the main supports to the main post using 5/8-11x10 hardware.  Tighten until the Main Support can be moved by hand with resistance.

image.png 20230519235617-931858db-sm.jpg

Cut two 5 ½” end pieces for the Main Support from 2x8 fragments.  Pre-drill 3/16” holes through the Main Support boards into the end pieces and attach using 5/16x4 leg screws.

Cut a 5 3/8” section of 4x4 post.  Drill a ½” hole through the middle of a side of the 5 3/8” section for attaching an eyelet.  Pre-drill 3/16” holes through the Main Support boards into the ends of the section and attach using 5/16x4 leg screws.

image.png

Horizontal & Vertical Supports

Cut two 4x4 post sections for Horizontal Supports to the length written on the worksheet (section 4.1).  Cut one 18” section of 4x4 post for the Pivot Arm.

Drill 9/16” holes through the center of a side of the Horizontal Support sections.  Drill a 9/16” hole in each end pieces, centered and 2” below the top edge.  Drill one additional hole in the rear end piece (away from the direction of the sun) 1 ½” above the bottom edge.  Use the end piece holes to template holes in the Pivot Arm with the top of the Pivot Arm flush with the top of the rear end piece.

image.pngScreenshot_2023-05-22_12-09-01.png

Attach the front Horizontal Support with 1/2x6 hardware. Attach the rear Horizontal Support and Pivot Arm to the upper hole using 1/2x10 hardware and secure the Pivot Arm to the lower hole using 1/2x6 hardware. Attach the Vertical Supports using 5/16x4 leg screws, pre-drilling 3/16” holes.


Solar Panel Mounts

Refer to the solar panel datasheet to determine the Panel Footprint Vertical and Panel Footprint Horizontal distances.

image.png

Drill 3/8” holes in each Vertical Support at 1 ½” from each end and at Panel Footprint Vertical + 1 ½” from each end. After drilling holes in the Vertical Support, drill 3/8” holes at the Panel Footprint Horizontal distance, toward the middle of the Horizontal Support (Figure 13).

image.pngimage.png

 

Prepare mount points for the solar panels by attaching one 5/16x8 bolt, three washers, and two nuts at each of the 3/8” holes drilled as shown in Figure 16. Leave approximately 1 inch of threaded length between the upper washer and end of the bolt. Leave the nuts at the wood supports finger tight so that the mount has some flexibility.

Attach each solar panel to a set of 3 mount points on the Horizontal and Vertical Supports. After installing a solar panel onto a set of mount points, fasten the panel to the mount points with 3 nuts and washers and tighten nuts at the solar panel and at the wood supports. After all solar panels have been mounted, adjust nuts as necessary to align each solar panel with respect to the others.

Screenshot_2023-05-22_12-19-26.png

 

image.png